Pcs Collet Set

4pc CAT40 ER16 Collet Chuck Tool Holder Set 3 Balanced G2.5 20000RPM New Cert

4pc CAT40 ER16 Collet Chuck Tool Holder Set 3 Balanced G2.5 20000RPM New Cert

4pc CAT40 ER16 Collet Chuck Tool Holder Set 3 Balanced G2.5 20000RPM New Cert    4pc CAT40 ER16 Collet Chuck Tool Holder Set 3 Balanced G2.5 20000RPM New Cert

We don't sell ER Collet Chucks, we sell ER Collet Chucks life! Draw Bar Thread: 5/8 -11. Concentricity/runout less than: 0.0001 / 0.003mm.

Collet Chuck accepts all ER16. Works on all CAT 40 machines. Certification included with each holder, documented TIR, taper accuracy and balance measurement. Tools are manufactured by an. Dynamically balanced to 20,000RPM at G2.5 by Haimer balancing machine at all location for consistent balance.

Unique design feature in the flange to minimize the off-balance nature of CAT 40 taper specification. On the shoulder under the flange, a side is mill flat to compensate the weight of the metal chips lost from forming the spherical hole in the flange. This design allows the left side and right side of the holder to achieve 50-50 perfect weight distribution in its upright position, like the position inside a machine spindle.

Symmetrical design in evenly weight distribution will minimize centrifugal force in high speed spinning and thus maximize the holder's ability to hold the cutting tool concentric to spindle rotation. In a generic standard ER collet nut, an internal ring is off-centered so that an ER collet can be easily snapped into it and holds the ER collet in place.

ER collet nut is optimized to distribute the flat sides' area to off-set the off-center. ER collet nut is also balanced with each holder. Manufactured from alloy steel with good core strength and long wear life. Taper shank is case hardened to 56-60 HRC and has a core hardness of 35-40 HRC. The case hardness is designed to give maximum wear life without compromising the 60-62 HRC spindle.

The core creates a damping effect from the vibration during the high speed milling, especially in long reach or heavy duty milling application. Taper ground to AT3 or better accuracy standard for maximum contact with spindle. All of SHARS CAT/BT/HSK tool holder use Stotz Air/Electronic Gaging for production and finish inspection. Stotz has been chosen by major aircraft companies as the best and most consistent gaging for tool holder shanks. All critical surface are precision ground. From taper to end mill pocket. Each holder comes with a lab certificate on its taper accuracy and runout measurement. Internal set screw is included and can be used as a stopping pin to prevent end mill or drill from sliding backwards while performing heavy cutting. Coolant through capability by removing the internal set screw. The inner holes will be inspected on product line one hundred percent by USA air jet instrument. The CAT40 CAT50 BT30 BT40 7:24 taper is inspected on production line by Stotz Air/Electronic instrument to ensure AT3 or better taper contact. Shars ER16 Clamping Hex Nut for CNC Milling Collets Chuck Holder Lathe. SHARS 7 Pcs 1/8 - 3/8 ER16 ER-16 COLLETS SET MILLING LATHE. Shars ER16 Collet Nut for CNC Milling Collet Chuck Holder Lathe.

SHARS Hex Type 25mm Open End ER16 Collet Spanner Wrench Milling. Shars Efficient CNC Tool Holder Storage Cart. SHARS 6 670V Milling Vise +/-0.0004. 6" wide jaw plate, 7.50" inner jaw opening, 15.80 outer jaw opening. Made from 80,000PSI stress relief cast iron.

Vise bed hardened to 45 HRc and jaw plate hardened to 54 HRc. Bed height Tolerance 2.875" +/-0.0005".

SHARS 6 660U Milling Vise +/-0.0004. 6" wide jaw plate, 6.25" inner jaw opening, 15 outer jaw opening. Single piece of stationary jaw and vise body to enhance clamping rigidness and accuracy.

Bed height Tolerance 3.189" +/-0.0005". SHARS 6 600DS Double Station Milling Vise +/-0.0002. 4.9" jaw opening in double station, 12" jaw opening in single station (conversion kit included). Unique leadscrew design to allow to clamp either same sized or dissimilar sized parts.

Jaw lift prevention mechanism by eccentric pin design. Bed height Tolerance 3.25" +/-0.0005" (matched bed height at no additional cost). The item "4pc CAT40 ER16 Collet Chuck Tool Holder Set 3 Balanced G2.5 20000RPM New Cert" is in sale since Tuesday, September 17, 2013. This item is in the category "Business & Industrial\Manufacturing & Metalworking\Metalworking Tooling\Toolholding\CAT Holders". The seller is "discount_machine" and is located in Saint Charles, Illinois. This item can be shipped to United States.
  • Brand: Shars Tool
  • MPN: 202-1451BG (4 pcs)

4pc CAT40 ER16 Collet Chuck Tool Holder Set 3 Balanced G2.5 20000RPM New Cert    4pc CAT40 ER16 Collet Chuck Tool Holder Set 3 Balanced G2.5 20000RPM New Cert